SCRD Document: Glossary of Drycleaning Terms

GLOSSARY OF DRYCLEANING TERMS

A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z

A

Adsorptive Cartridge Filters - Filters that contain clay or clay and activated carbon. These filters are designed to remove insoluble soil and non-volatile residue along with dyes from solvent. See Cartridge Filters.

Aeration - See Deodorizing Cycle.

Air Bumping - See Bumping.

Amyl Acetate – A dry-side spotting agent used to remove oil base stains and plastics.

Anionic Detergent System - A drycleaning detergent that is negatively charged. These detergents carry water by solubilization. Anionic detergents are used in charged systems.

Anti-foaming Agents - These chemicals are sometimes added to the distillation unit to prevent contaminants contained in spent solvents (such as pigments, acids, filter powder, detergents, water repellents and retexturing agents) from causing excessive foaming during the distillation process. Glycol ether acetate has been utilized as an anti-foaming agent.

Atmospheric Still - A distillation device that operates without the need for internal pressure or vacuum. All drycleaning stills designed for use with chlorinated solvents are atmospheric.

Assembly - Following the finishing step in the drycleaning process, the garments are sorted and assembled - generally placed on hangers and covered with plastic bags. This is the final step in the drycleaning process.

Azeotropic Distillation - The distillation of a mixture with components having constant maximum and minimum boiling points, with the components being distilled without decomposition, and in a fixed ratio.

B

Backwashing - A method used to remove spent powder filtration material (diatomite) from tubular filters. In this operation, the solvent flow is reversed to wash the spent filter powder off the tubular filters. See Bumping.

Bactericides - a.k.a. biocides – These are chemicals used to prevent biodegradation of petroleum drycleaning solvents. Bactericides are commonly contained in drycleaning detergents

Bag Filter - A type of filter that collects lint from the drying cycle. or A filter that was used in powder filtration systems. The bag filter was coated either inside or outside with filter powder which trapped the soils. The bag was held in place by a frame and when full or clogged the frame was removed. The messy handling hastened the disappearance of this type of filter.

Base Tank - A solvent storage tank located at the base of a drycleaning machine. Normally there are two or three of these per machine. One base tank contains clean solvent and one contains dirty solvent to be distilled.

Bath Operation or Bath System - In this drycleaning solvent system, a fixed quantity of solvent is issued for one operation. Solvent is not circulated during the wash cycle. Solvent introduced in the washer is used for the entire load.

Batch Operation - A drycleaning solvent system in which there is continuous circulation of drycleaning solvent. Detergent and sometimes water are added into a wash solvent tank. The entire wash solvent is “charged” with detergent (or detergent is injected). The concentration of detergent in this charged system is one to two percent. This is also known as Batched Detergent Injection.

Belly Washer - A type of washer used in a transfer machine operation. Belly washers consist of a metal shell with a perforated inner cylinder. The shell contains the solvent and the cylinder holds the garments. The size of the cylinder ranges from 30 x 30 inches to 53 x 70 inches. The cylinder of the belly washer is mounted on a horizontal shaft which rotates - providing agitation. Clothing is washed in solvent in the belly washer. Solvent extraction is performed in some machines. However, extraction is not performed in the older petroleum-type washers. In these operations, the clothing must be transferred to an extractor. After solvent extraction, the clothing is transferred to a tumbler (dryer). Belly washers are virtually obsolete in the today’s drycleaning industry.

Benzine - See Naphtha.

Bleach - A chemical or chemical mixture used in pre-spotting, spotting and laundry operations to decolorize stains and soiled areas. There are two types of bleaches: oxidizing and reducing.

Body Feed - The fresh filter powder (diatomite) added at the beginning of each filtration cycle in a non-regenerative powder filtration system.

Boil Down - The last phase of the solvent distillation process in which the still kettle temperature is increased to recover additional solvent.

Boiler - An enclosed vessel in which water is heated and circulated either as hot water or steam. Drycleaning operations utilize boilers as a heat and steam source for distillation operations; heating air for drying operations; pre-cleaning and spotting operations; steam pressing operations; steam cleaning of equipment, and steam stripping of carbon adsorption units and cartridge filters.

Boiler Blowdown Water - Water generated from the process where the steam and water is discharged from the boiler. This discharge blowdown is part of boiler maintenance to prevent scale buildup.

Boiler Feed Water Treatment - These are chemical treatments used to prevent scale buildup and/or prevent corrosion in boilers. The chemicals are either buffering agents (alkaline salts such as potassium hydroxide), oxygen scavengers (such as sodium bisulfite), and chelating agents (such as sodium hexametaphosphate). Hydrochloric acid is sometimes used to remove scale from boilers.

Boilover - The Discharge of still bottoms/muck from a distillation unit or muck cooker. The cause of boilover is usually caused by overfilling the distillation unit/muck cooker but can be caused by operating the unit at too high a temperature.

Bound Moisture - Water held and dispersed by a detergent in a drycleaning solvent.

Buck – The bottom plate of a steam press. The garment to be finished (pressed) is placed on the buck.

Bump Action Filters - See Regenerative Filters.

Bumping - The removal or dislodging of spent powder filtration material (diatomite and activated carbon) from flexible tubular filters by flexing or agitating or by using compressed air (air bumping).

Button Trap - A drycleaning machine device located in front of the solvent pump that prevents objects (lint, fasteners, buttons, coins etc.) from entering the solvent pump.

Butyl Hydroxyl Toluene (BHT) - An antioxidant commonly added to petroleum drycleaning solvents to prevent odor problems (odor inhibitor). Some re-claimed PCE contains BHT as an additive (color inhibitor). Also known as Butylated Hydroxyl Toluene.

C

Camphor Oil – Oil derived from the wood of a camphor tree. Camphor oil was reportedly used as an early drycleaning solvent (19th century).

Carbona - The trade name under which carbon tetrachloride was formerly marketed as a drycleaning solvent and spotting agent.

Carbon Adsorber - A bed of activated carbon into which an air-solvent vapor stream is routed and which adsorbs the solvent on the carbon. Carbon adsorption systems can handle high air flow rates with low solvent concentrations and reduce solvent vapors in exhaust by 95%. Also known as a Vapor Adsorber or Sniffer.

Carbon Tetrachloride - This was the first chlorinated solvent to be used in drycleaning operations (beginning in the 1920s). Carbon tetrachloride is no longer used in drycleaning operations (use ended some time in the early 1950s) because of its high toxicity and corrosiveness. Carbon Tetrachloride is also known as Tetrachloromethane. See Carbona.

Cartridge Filter - A replaceable filter used in the wash cycle consisting of an outer metallic perforated shell enclosing a pleated paper filter element around a perforated activated carbon or clay-filled canister having a central perforated center post with a fine-mesh wrap. Cartridge filters are the most widely used filters in drycleaning today.

Cationic Detergent - A drycleaning detergent that is positively charged. Cationic detergents carry water by means of an emulsion. They provide excellent water-soluble soil removal. These detergents are used in injection systems. See injection system.

Centrifugal Disc Filter - See Spin Disc Filter.

CFC-113 - See Valclene.

Charged System - A drycleaning solvent/detergent system in which detergent is added to the solvent or “charged” as a certain percentage of the solvent (normally 1 to 2%) to maintain a continuous concentration of detergent. Charged systems use anionic detergents.

Chiller - See Refrigerated Condenser.

Clarifying System – In early drycleaning operations spent solvent was routed to a tank or series of tanks where solids settled out of the solvent. The “clarified” solvent was reused.

Classification - In the drycleaning operation, this is the separation of clothes into similar groups that may be drycleaned together. This separation involves classifying garments on the basis of their weight, color, and finish before cleaning. This breakdown assures that clothes cleaned together are compatible and receive treatment appropriate for their type.

Clean Air Act Amendments (CAAA) - The 1990 amendments to the Clean Air Act (1970) added comprehensive provisions to regulate emissions of toxic air pollutants, acid rain, and substances that threaten the ozone layer. Additionally, the 1990 amendments added a permit program and greatly strengthened enforcement provisions and requirements for non-attainment areas, mobile source emissions, and automotive fuels.

Cleaners Naphtha - Another name for Stoddard Solvent. See Stoddard Solvent.

Closed-loop Machine - A dry-to-dry machine which recirculates solvent-laden vapor through a primary control system (e.g. refrigerated condenser) with no exhaust to the atmosphere during the drying cycle. A closed-loop machine may allow for venting to the ambient air through a local exhaust ventilation system, such as a door fan, after the drying cycle is complete and only while the machine door is open.

Closed-Loop Solvent Delivery System - A drycleaning solvent delivery system that includes a stainless steel drum which contains the solvent and a two-wheeled dolly that transports the drum and carries a pump for transferring the solvent to the drycleaning machine or solvent storage tanks. The solvent is pumped through a hose equipped with “leak proof connections” that couples with a filling port on the drycleaning machine.

Coin-Operated Drycleaning Machine - A dry-to-dry machine normally located in a self-service laundry that is operated by the customer. Coin-operated drycleaning machines were introduced in 1960. They have small capacities (8-10 pounds of clothes). Some early coin-operated drycleaning machines utilized powder filtration systems (diatomaceous earth and activated carbon) but most machines utilize cartridge filters for solvent purification. A few of the coin-operated drycleaning machines utilized valclene but, by far, most of the machines use PCE.

Cold Machine - A tumbler (dryer) that does not utilize heated air..

Cold Spotting Board - A spotting board that is not supplied with steam. See Spotting Board.

Combination Machine or Combination Washer/Extractor - A transfer machine in which the clothes are washed and the solvent is extracted before the clothing is transferred to a tumbler. Also known as a Dry-to-Damp System.

Commercial Drycleaners - Those drycleaners engaged primarily in drycleaning apparel and household fabrics other than rugs.

Condensate Water - Any drycleaning wastewater derived from the condensation of distilled solvent vapors, dryer vapors, or steam.

Condenser - A device used to chill hot solvent vapors and recover liquid solvent. Condensers are generally used during the drying cycle and when operating the still, muck cooker, or vapor recovery unit.

Constant Pressure Filter - A powder filtration system in which constant solvent pressure is exerted on the filter in order to keep the filter coated with filter powder.

Contact Water - Any wastewater stream that has been in contact with drycleaning solvents or drycleaning solvent vapors. Contact water, therefore, contains solvent.

Converted Machine - An existing vented drycleaning machine that has been modified to be a closed-loop machine by eliminating the aeration step, installing a primary control system, and providing for recirculation of solvent-laden vapor with no exhaust to the atmosphere or workroom during the drying cycle. A converted machine may allow for venting to the ambient air through a local exhaust ventilation system, such as a door fan, after the drying cycle is complete and only while the machine door is open.

Cooked Powder Residue - The waste material generated by cooking down or distilling muck. Cooked powder residue is a hazardous waste and will contain solvent, powdered filter material (diatomite), carbon, non-volatile residues, lint, dyes, grease, soils and water.

Cooker - See Muck Cooker.

Cool-down - The portion of the drying cycle that begins when the heating mechanism deactivates and the refrigerated condenser continues to reduce the temperature of the air recirculating through the drum to reduce the concentration of solvent in the drum.

Custom Cleaner Home Drycleaning Kit - A home drycleaning product that is used to clean clothing in a conventional dryer.

Cylinder - The rotating drum of a drycleaning machine or dryer where the clothes are placed.

D

Decamethylcyclopentasiloxane - (a.k.a. D5) See GreenEarth.

Dry-to-Damp System - See Combination Machine.

Deodorizing Cycle - The last stage of the operation of the reclaiming dryer. At this point, the air inlet and exhaust valves are opened and a stream of cool outside air strips away the last solvent vapors. If properly done, the clothing should be left dry and virtually odor-free. Also known as Aeration.

Desorption - Regeneration or stripping of an activated carbon bed, or any other type of vapor adsorber by removal of the adsorbed solvent using hot air, steam or other means.

Detergent - An additive routinely added to solvent to assist in removing water-soluble soils and stains that are not ordinarily soluble in solvent alone.

Detergent Test Kit - Chemical agents used to titrate solvent/detergent mixtures to measure the amount of detergent contained in charged detergent systems. Some of the chemicals used in the kits include: 1,2-dichloroethane, methylene chloride and chloroform.

DF-2000TM - A petroleum drycleaning solvent manufactured by Exxon Chemical. DF-2000™ is a synthetic hydro-treated aliphatic hydrocarbon blend (reported to be predominantly C11 – C12 aliphatic hydrocarbons) that has a flashpoint of 147° F and a specific gravity of 0.77 at 60° F.

Diatomaceous Earth or Diatomite - A siliceous powder composed of the remains of microscopic single cell aquatic plants. It is used as the filter media in powder filtration systems. This powder builds up on a supporting frame and forms a porous surface. Also known as Filter Powder.

Digestive Agent - A pre-cleaning or spotting agent which is a mixture of enzymes used to digest food and albuminous-type stains.

Distillation - A process by which solvent is separated from non-volatile and other impurities by boiling The used or contaminated solvent is heated and vaporized, then condensed into a solvent/water mixture, which after separation yields a pure solvent. The contaminants are left behind as a residue or sludge.

Distillation Bottoms or Distillation Residues - See Still Bottoms.

Diverter Valve - A flow control device that prevents room air from passing through a refrigerated condenser when the door of the drycleaning machine is open.

Door Fan - A local exhaust ventilation system designed to provide for a minimum 100 fpm inward air velocity or equivalent into the effective door open area of a drycleaning machine whenever the door is opened, and where the solvent emissions are controlled by a carbon adsorber or equivalent control prior to venting to the outer air.

Dosimeter Badge - A device for measuring the amount of organic vapors a person is exposed to during a set time period, or the vapor concentration in a given area.

Dowclene Ls - Trade name under which 1,1,1-trichloroethane (TCA) was formerly marketed as a drycleaning solvent by Dow Chemical.

Dow-per– Trade name for drycleaning perchloroethylene manufactured by Dow Chemical.

Drop-off Facility - See Dry Drop-off Facility.

Drum - See Cylinder.

Drycleaner’s Secret– A home drycleaning product marketed by Dry Inc. A “sheet” containing the product is placed with the clothing to be cleaned in a conventional dryer.

Drycleaning - The process used to remove soil, greases, paints and other unwanted substances from articles with organic solvents.

Drycleaning Control System - Equipment (e.g. carbon adsorber, refrigerated condenser, azeotropic unit, etc.) or an air cleaning device used to reduce the amount of air pollutants in an air stream prior to discharge to the atmosphere.

Dryel – A home drycleaning product developed by Proctor & Gamble. Clothing is placed in a bag containing the product and the bag is placed in a dryer. Vapors, activated from the heat of the dryer penetrate the clothing and “lift” the odors and soils from the clothing.

Drycleaning Machine - A dry-to-dry machine and its ancillary equipment or a transfer machine system and its ancillary equipment.

Drycleaning Solvent - Nonaqueous solvents used in the cleaning of clothing and other fabrics.

Dry Drop-off Facility - A commercial retail store that receives from customers clothing and other fabrics for drycleaning at an off-site drycleaning facility and does not clean the clothing or fabrics on site. Also known as Dry Drop-off, Drop-off Facility, or Dry Store.

Dryer - See Reclaimer and Tumbler.

Drying Cabinet - A housing in which materials that have been previously drycleaned in solvent are dried instead of being dried by tumbling in a drycleaning machine. Solvent can be recovered from cartridge filters by a drying cabinet. Air or steam is pulled over cartridges and then routed to a carbon adsorber where it can be recovered by stripping and separation. Also known as a Steam Cabinet.

Drying Cycle - The operation used to actively remove the solvent remaining in the garments after washing and extraction. For closed-loop machines, the heated portion of the cycle is followed by cool-down and may be extended beyond cool-down by the activation of a control system. The drying cycle begins when heating coils are activated and ends when the machine ceases rotation of the drum.

Drying Efficiency - See Reclamation Efficiency.

Dry-side Spotting Agent - Solvents used to pre-clean or “spot clean” non-water soluble stains or soils. Some examples of chemicals that have been utilized as dry-side spotting agents are: perchloroethylene, trichloroethylene, 1,1,1-trichloroethane, carbon tetrachloride, petroleum solvents and amyl acetate.

DrySolvTM - A drycleaning solvent composed of n-propyl bromide (a.k.a. 1-bromopropane). DrySolv is stabilized with nitromethane and 1,2-butylene oxide. DrySolv was first marketed in 2006 by Dry Cleaning TechnologiesTM, a division of Environ Tech International, Inc.

Dry Store - See Dry Drop-off Facility.

Dry-to-Dry Machine - A drycleaning machine, in which both cleaning and drying cycles are performed in the same wash wheel. Because the dry-to-dry machine is completely enclosed during the entire cycle, releases of solvent fumes to the plant atmosphere are minimized. Also known as a “Hot” Machine.

Dry Wetcleaning – A relatively new cleaning process whereby clothing is cleaned in a specially designed machine that utilizes a combination of jet air pulsating, tumbling and blotters or felt pads to clean clothing. A detergent (DWX-44) described as a mixture of water and surfactants is also used in the process.

Dyna CleanTM System - A drycleaning solvent purification system that utilizes azeotropic distillation.

Dyna PurTM Process - A solvent purification process that employs a permanent stainless steel filter with a fabric lining. Dirt and other contaminants are routinely backwashed off the filter with clean solvent. The contaminated solvent is distilled azeotropically to separate the perc from other components. As with other systems, the solvent/water vapor mixture produced during distillation is condensed and the solvent and water are separated. The steam condensate contains soils, other contaminants, and any perc residual is then discharged.

E

EcoSolv™ - A petroleum drycleaning solvent manufactured by Chevron Phillips Chemical Company LP. It is reportedly composed of C10 – C13 hydrocarbons and has a flashpoint of 142° - 144° F and a specific gravity of 0.762 at 60° F. EcoSolv was formerly known as HC-DCF High Flash ™.

EPA Identification Number - A unique number assigned by EPA to each generator or transporter of hazardous waste and each hazardous waste treatment, storage or disposal facility.

Equivalent Closed-loop Recovery Systems - A device that volatilizes solvent from the waste stream in a single pass prior to discharge.

Evaporator - A wastewater pre-treatment device that volatilizes solvent from the waste stream in a single pass prior to discharge. Normally, the water is filtered through an activated carbon or polymer filter to reduce solvent concentrations.

Exhaust Damper - A flow control device that prevents the air-solvent vapor stream from exiting the drycleaning machine into a carbon adsorber before room air is drawn into the drycleaning machine.

Extraction - The step that usually follows immediately after the completion of the wash cycle and drain period. During extraction, the wash wheel is accelerated to speeds of 350 to 450 rpm, causing much of the solvent to spin free of the fabric.

Extractor - A vertical axis centrifuge which removes most of the drycleaning solvent from the clothing after the “wash” phase is finished.

F

Fifth Generation Machine – A non-vented, closed loop process drycleaning machine (dry-to-dry) with both carbon adsorption and refrigerated condensers utilized to reduce residual solvent in the machine cylinder at the end of the dry cycle to concentrations below a certain level (generally 300 to 100 ppm). Fifth generation machines have inductive fans and lockout devices that do not allow the machine door to be opened until solvent vapor levels have been reduced to low levels.

Filter Cake - See Muck.

Filter Muck - See Muck.

Filter Powder - See Diatomaceous Earth.

Filter Soap - An early drycleaning detergent composed of petroleum sulfonates and other sulfanates. These soaps are soluble in drycleaning solvent and can therefore pass through filters, hence the name filter soaps.

Finishing - Pressing of garments to remove wrinkles and restore each garment to its original size, shape and appearance. Pressing equipment is heated with superheated steam.

First Generation Drycleaning Machine - See Transfer Machine.

140° Flash Solvent - A petroleum distillate drycleaning solvent with a higher flash point (flash point of 140° F) than common petroleum solvents, thus reducing its fire hazard. The distillation range for this solvent is 350 - 410°F. Also known as 140° F Solvent.

Flat Screen Filter – A type of solvent filter constructed of woven Monel metal wire. Flat screen filters were used in powder filtration systems and succeeded bag filters.

Flexible Tube Filters - See Regenerative Filters.

Form Finisher - See Suzie.

Fourth Generation Drycleaning Machine - A non-vented, closed loop process machine (dry-to-dry) with an additional internal vapor recovery device. The control technologies used in these machines are refrigerated condensers and carbon adsorbers.

Freon 113 - See Valclene.

Fresh Care - A home drycleaning product manufactured by Clorox.

Fugitive Vapors - Vapors that escape from process equipment (such as a drycleaning machine).

Full-size Carbon Unit - A carbon unit that is used to adsorb solvent from a drycleaning machine when the vapors are recirculating or venting from the drum during the drying cycle (normally used on first and second generation equipment).

G

Gasoline - Gasoline (reportedly white gasoline) was the predominant drycleaning solvent in the United States in the early twentieth century, particularly from 1910 – 1920.

General Exhaust Ventilation System - A mechanical exhaust ventilation system consisting of fresh air makeup inlets and one or more exhaust fans in a drycleaning facility, that primarily exhausts a drycleaning workroom; also used with a room enclosure.

GEN-X - A drycleaning solvent marketed by Caled Industries. It is a blend of petroleum hydrocarbons (hydrotreated heavy naphtha) and aliphatic propylene glycol ether.

Graying - Discoloration of garments caused by soil particles flocculating or being adsorbed back onto the garment surface. The chief cause of graying is dirty solvent.

GreenEarth - GreenEarth is a silicone-based drycleaning solvent (chemical name is decamethylcyclopentasiloxane) developed by General Electric and offered as an alternative to chlorinated and petroleum-based drycleaning solvent. It has a flash point of 170 ° F and a specific gravity of 0.95.

Green-JetTM Dry-Wet Cleaning Machine - Green Jet is a cleaning machine manufactured by Aero-Tech USA that cleans and dries garments. The first step in the cleaning process is the reduction of humidity in the drum of the machine. Non-soluble soil is then removed from garments by rotating the drum and pulsing air through jets. The soil is collected in a lint chamber. A water-based cleaning solution known as DWX-44 and described as a surfactant blend (detergent), is injected through the air jet nozzles to re-hydrate the fabric. Soluble soil is adsorbed by felt pads attached to the cylinder of the machine. The last step in the process is drying and a cool-down cycle.

Grid-Head Press - A type of steam press that has a perforated head, porous to steam and air. The grid-head press is used on woolen and woolen-type garments.

H

Halogenated-hydrocarbon Detector - A portable device capable of detecting vapor concentrations of perchloroethylene and indicating an increasing concentration by emitting an audible signal or visual indicator that varies as the concentration changes.

Heating Coil - A device used to heat the air stream circulated from the drycleaning machine drum after perchloroethylene has been condensed from the air stream and before the stream reenters the drycleaning machine drum.

Hot-Head Press - A type of steam press with a smooth, non-porous stainless steel head. The head is heated by steam to surface temperatures as high as 300° F. The hot-head press is used to finish silks and silk-like fabrics.

Hot Machine - A tumbler (dryer) that utilizes heated air.

Hot Plate Evaporator - A device that utilizes a heating coil to vaporize (or boil-off) wastewater at a drycleaning facility – primarily separator water and vacuum press water.

Hydroclene® Drycleaning Fluid - A high-flash (flashpoint 145° F.) petroleum drycleaning solvent manufactured by Shell Chemical Company. Hydroclene Drycleaning Fluid is marketed by Caled Industries.

Hydrogen Peroxide - A common oxidizing bleach used in pre-cleaning and spotting operations. Normally a 3% hydrogen peroxide solution is used. Hydrogen peroxide is used to remove organic stains.

I

ImpressTM - A propylene glycol ether based drycleaning solvent first marketed in 2004 by Lyondell Chemical Company.

Inductive Fan - A fan in a drycleaning machine that draws air into the machine when the machine door is opened. This reduces exposure to the drycleaning workers to emissions of solvent vapors.

Industrial Cleaners - Those drycleaners engaged in supplying laundered or drycleaned work uniforms, wiping towels, dust control items etc. to industrial and commercial users.

Injection System - A drycleaning solvent/detergent system in which solvent is added to the wheel saturating the garments and then detergent is injected into the flow line or into the drum by a pump or dump method. Cationic detergents are used in injection systems.

Insoluble Soil - The most commonly found materials in fabrics and the bulk of the soils removed in the drycleaning process. Examples include earth, concrete dust, sand, carbon, ashes, lint, hair and cosmetics, etc. These soils will not dissolve either in drycleaning solvent or water. Insoluble soils are removed in the drycleaning machine by lubrication and emulsification.

International Fabricare Institute (IFI) - A private international organization headquatered in Silver Spring, Maryland, that represents professional drycleaners. IFI provides research, testing services, and education for drycleaners. Website

J

Jumbo Split Cartridge Filter - A cartridge filter (carbon, carbon-clay mix or carbonless) whose dimensions are 3 1/4 inches by 9 inches.

Jumbo Full Size Cartridge Filter - A cartridge filter (carbon, carbon/clay mix or carbonless) whose dimensions are 13 1/4 inches by 18 1/8 inches.

K

Kauri-Butanol Value (KBV) - The solvent-soluble soil removing capability of a liquid. A solvent with a high KBV values is usually more efficient in removing oil and grease stains, but a lower KBV value may be safer on some dyes, adhesives, and trim fabrics.

Kissing Tumblers - An automated transfer system in which the washer and dryer can move together in such a manner that garments will be moved by gravity from the washer to the dryer as the units drums rotate. The cost and complexity of this approach have limited its application to industrial systems.

L

Laundering - In contrast to drycleaning which uses a solvent as the principal cleaning medium, wetcleaning uses water. This process may be used occasionally by a drycleaner when a drycleanable garment is heavily stained with water soluble soils. Also known as Wet Wash.

Leveling Agent - A textile industry term referring to a wetting agent used to aid in the uniform dispersal of a dye in a dye bath and generally having wetting properties. Leveling agents emulsify water molecules. Leveling agents are also employed to facilitate the use of wetside spotting agents and obtain the removal of water rings on garments.

Liquid Carbon Dioxide - A cleaning process whereby carbon dioxide in a liquid state (operating under a pressure of approximately 700 pounds per square inch) is utilized as a cleaning solvent. The first commercial liquid carbon dioxide drycleaning plant opened in Wilmington, North Carolina in 1999.

Loading Factor - The optimum weight of clothes that can be properly cleaned in a particular machine. This takes into account the size of the wheel (or tumbler), the type of process used, and the solvent used.

M

Mahogany Sulfate - See Petroleum Sulfonates.

Marking - Process of identifying garments by attaching tags to each garment or stamping an identification code onto an inner surface of the garment. It is the first operation performed in a drycleaning plant.

Methyl Chloroform – See 1,1,1-Trichloroethane

Mileage - See Solvent Mileage.

Mister - A wastewater treatment device that sprays drycleaning wastewater that has been filtered through activated carbon or polymer filter into the air for disposal.

Montreal Protocols - An international environmental agreement to control chemicals that deplete the ozone layer. The protocol which was renegotiated in June 1990, calls for a phase-out of CFCs, halons, and carbon tetrachloride by the year 2000, a phase out of chloroform by 2005 and provides financial assistance to help developing countries make the transition from ozone depleting substances.

Muck - The residue from a powder filtration system which consists of diatomite (diatomaceous earth), spent solvent, non-volatile residues, greases, lint, soils, water, and sometimes carbon. Also known as Filter Cake or Filter Muck.

Muck Cooker - A distillation device in which live steam is used to heat solvent-laden waste (muck) from powder filtration systems to volatilize and recover solvent. Also known as a Cooker.

N

Naphtha - A petroleum or coal tar distillate composed largely of aliphatic hydrocarbons. Naphtha has been used as a drycleaning solvent. Also known as Benzine.

National Emission Standards for Hazardous Air Pollutants (NESHAP) - Air standards for pollutants proposed in December 1991 under the Clean Air Act Amendments. Promulgated in 1993, NESHAP requirements for the perchloroethylene drycleaning industry prohibit the sale of new transfer machines, require retrofitting of existing drycleaning equipment with control devices and require new machines to be sold with such equipment.

Non-ionic Detergent - A drycleaning detergent that has no charge. These detergents carry water by means of solubilization. Non-ionic detergents are used in charged systems.

Non-recovery Unit - See Tumbler.

Non-volatile Residue (NVR) - The bulk of the residue left in the still after the solvent has been distilled out. NVR is made up primarily of oily, fatty, gummy and insoluble soils removed from clothing.

n-propyl bromide - See DrySolvTM or Tech Kleen®.

O

Optical Brighteners - a.k.a. fluorescent whitening agents, optical bleaches or optical dyes. Chemicals used to “make white whiter”. Optical brighteners are normally included in detergents or sizing.

Oxidizing Bleach - A bleach that utilizes an oxidation process to decolorize stains or soiled areas. Examples are: sodium perborate, hydrogen peroxide, sodium hypochlorite and sodium perborate.

P

PCE - See Perchloroethylene.

Perc - See Perchloroethylene.

Percent Detergent - The ratio of detergent to solvent used in the drycleaning cycle. Most charged solvents contain a “percent detergent” between one half and one and one-half percent, depending on the drycleaning system being used.

Perchloroethylene - A completely halogenated (chlorinated) ethene. This chlorinated hydrocarbon has excellent cleaning and degreasing properties, and is the predominant solvent used in the drycleaning industry. Also known as Tetrachloroethylene, Tetrachloroethene, Perc or PCE.

PerkloneTM -Perklone is the trade name for perchloroethylene drycleaning solvent manufactured by Ineos Chlor and exported to the United States. Ineos Chlor exports two brands of perchloroethylene drycleaning solvents: PerkloneTM D and PerkloneTM DX.

Per Sec® - Trade name for perchloroethylene drycleaning solvent manufactured by Vulcan Chemicals.

Petroleum Drycleaning Solvents - Drycleaning solvents that are petroleum based. These are solvents are blends of distillate fractions produced at petroleum refineries. Most are mixtures of as many as 200 different compounds and have a variable composition (generally C5 - C16). Their flash points range from 105° F to 147° F. (New higher flash point so-called synthetic petroleum solvents are being developed). There are many names for these solvents including: Stoddard solvent, mineral spirits, 140° flash solvent, quick-dry solvent, etc. The earliest petroleum drycleaning solvents were kerosene, gasoline, benzene and naphtha.

Petroleum Sulfonate - An early drycleaning detergent (a filter soap). It is a sulfonate of mixed hydrocarbons of petroleum origin. Petroleum sulfonates was the original charged-system detergent. Also known as Mahogany Sulfonate.

Petro-miser - Petroleum solvent dryer (reclaimer) that reclaims petroleum solvent.

Picrin - Trade name for one of the more commonly used dry-side spotting agents. The predominant constituent of Picrin is trichloroethylene.

Polishing Filter - A filter used to remove small particles of carbon or soil that have not been captured by the main filter and can effectively minimize redeposition of soil on the garments - known as “graying”. Polishing filters have pore sizes that are extremely fine (3 to 5 microns). They are installed downstream of the main filter system. There are two types of polishing filter mediums - resin-bonded fibers and a spiral cotton element.

Powder Filtration System - Drycleaning filtration systems that utilize filter powder (diatomite) and sometimes filter powder plus activated carbon as a filtering medium. These systems can be either Constant Pressure Filters, or Regenerative Filters.

Pre-charged Solvent - Drycleaning solvent that contains detergent added by the manufacturer. It has been used largely in coin-operated drycleaning machines.

Pre-cleaning - See Spotting.

Precoat - Filter powder applied to the tube filters or filter mesh.

Precoating - Placing a thin layer of filter powder on the filtering medium (screen, tube disc) before any impure solvent has passed through the screen holes. Precoating prevents the clogging of the holes by providing an immediate layer of filter powder as the first impurities come through

Pre-spotting - See Spotting.

Press Return Water - See Vacuum Water

Protein Formula Detergent - A type of wet-side spotting agent that contains enzymes, which can include Amylase, Cellulase, Lipase or Protease. These digesters are used to remove starch, cellulose, fats, oils and protein stains.

Pump Strainer - A device located in front of the solvent pump in a drycleaning machine that prevents lint and other objects from entering the pump.

PureDry™ - A so-called “hybrid” drycleaning solvent manufactured by Niran Technologies, Inc. PureDry is a blend of petroleum hydrocarbons (isoparaffins), perfluorocarbons and hydrofluoroethers (HFEs). It has a flash point of 350 ° F and a specific gravity of 0.8 at 77° F.

R

Rag Filter - A cloth filter (generally terry cloth) located in a water separator to remove moisture from the distilled solvent as it comes from the still and to traces of rancid materials that may have passed through the distillation unit. Rag filters are used almost exclusively in petroleum solvent drycleaning operations since water/solvent separation is not as efficient in these operations.

Reclamation Efficiency - A measure of the efficiency of the reclaiming dryer or drying cycle in extracting solvent from the clothing. Also known as Drying Efficiency.

Reclaimer - A machine used to remove solvent from clothing by tumbling them in a heated air stream. The solvent vapors are then condensed and routed to a water separator, where the solvent is separated from the water. Also known as a Reclaiming Dryer or Recovery Dryer.

Reclaiming Cycle - The first stage in the drying or reclaiming process, in which solvent remaining in the garments is vaporized by a stream of hot air. The vapors are then condensed and the liquid solvent drawn off and stored for reuse.

Reclaiming or Recovery Dryer - See Reclaimer.

Recovery Unit - See Reclaimer.

Recycle - A process of preparing a solvent for re-use. In drycleaning, this is done by filtering and distilling the drycleaning solvent after it has removed the soil from the clothes. Solvent can be recycled repeatedly by a drycleaner.

Redeposition - The return of insoluble soil to the fabrics from which it was freed during the cleaning cycle. dispersal and redeposition of insoluble soils is the principal cause of “graying”.

Reducing Bleach - A bleach that decolorizes stained or soiled areas through a reducing reaction. Examples of reducing bleaches are: sodium bisulfite, sodium hydrosulfite, titanium stripper and oxalic acid.

Refrigerated Condenser - A vapor recovery system into which an air-solvent gas-vapor stream is routed and the solvent is condensed by cooling the gas-vapor stream. Refrigerated condensers recover solvent emissions by chilling the air stream below the solvent’s dew point, causing the solvent and water vapor to condense.

Refrigerated condensers can be placed either in the air stream near the end of the drying cycle or at the final exhaust point of the process. In transfer machines equipped with refrigerated condensers, the air stream received from the washer when the door is opened is typically vented to the atmosphere after one pass through the condenser. Thirty percent of the solvent is typically recovered. Vapors from the drying unit are continually routed back to the dryer after passing through the condenser until the drying cycle ends. Eighty-five percent of the remaining solvent is typically recovered. Unrecovered vapors are vented to the atmosphere when the dryer is opened.

In vented, dry-to-dry machines equipped with refrigerated condenser, emissions occur when the door is opened. No-vent or closed-loop machines do not vent to the atmosphere and have the highest efficiency in recovering emissions. Also known as a Chiller.

Refrigerated Condenser Coil - The coil containing the chilled gas (usually CFC 11 or CFC 12) used to cool and condense the solvent.

Regenerative Filters - The most widely used type of powder filtration system. It consists of flexible tubes that are constructed of braided metal wire, metal helical springs or braided knit fibers. The filter powder, which is the filter media, is held by the flexible tubes. Spent powder is removed or “bumped” and then the regenerated or pre-coated each day or after each load has been run. Also known as Flexible Tube Filters or Bump Action Filters.

Rigid Tube Filter - A type of non-regenerative filter in which the precoat is supported on an internal wire frame surrounded by a filter screen. Backwashing is used to remove the filter cake from these filters.

Room Enclosure - Stationary structure that encloses a transfer machine system. These enclosures are designed to contain solvent vapors which are vented to a carbon adsorber or an equivalent control device during operation on the transfer machine system.

Rynex - A drycleaning solvent that is composed of dipropylene glycol tertiary-butyl ether. It has a flash point of 203° F and a specific gravity of less than 0.95.

Rynex III - Rynex III is a more recent formulation of the drycleaning solvent Rynex. It is a mixture of glycol ethers more specifically dipropylene glycol tert-butyl ether or DPTB.

S

Screen Filters - Fine mesh screen held in a vertical plane with nipples that feed into a manifold. Screen Filters are used in powder filtration systems. The solvent surrounds the screens where the powder collects and strains insolubles out as the solvent flows through and into the manifold and out. A variation of this type of filter employs a series of horizontal circular screens between each of which is a brush which automatically rotates for cleaning . This filter operates with a blend of sweetener powder and carbon and is automatic in its dispensing of powders and self cleaning. Very few screen filters are in use today.

Second Generation Drycleaning Machine - See Vented Dry-to-Dry Machine.

Separator Water - Wastewater generated from the physical separation of drycleaning solvent and water in a water separator. Separator water is a contact water and therefore contains solvent.

Shell Sol 140 HT - A high flash point petroleum solvent (flash points 145° F) manufactured by Shell Chemical Company. Shell Sol 140 HT is composed of a mixture of C9 – C12 hydrocarbons.

Sixth Generation Machine - A term used by some to refer to dry-to-dry machines that utilize GreenEarth drycleaning solvent.

Sizing - A type of finish used in drycleaning to impart body to a fabric. Most sizing used in drycleaning operations is composed of hydrocarbon resins and comes in either a solid form (powder or beads) or a liquid. In its liquid form the sizing is generally combined with a petroleum naphtha carrier. Anti-static agents and optical brighteners are commonly added to sizing.

Slide Board – A metal-lined chute utilized in a transfer machine operation to transfer clothing from a washer to an extractor.

Sludge - See Still Bottoms.

Sniffer - See Carbon Adsorber.

Sodium Bisulfite - A reducing bleach used in pre-cleaning and spotting operations. Its main use is in removing the last traces of chlorine bleach.

Sodium Hydrosulfite - A reducing bleach used in pre-cleaning and spotting operations.

Sodium Hypochlorite - The most commonly used oxidizing bleach. It is normally packaged as a 5% solution but is used in pre-cleaning and spotting operations in a 1% solution. Sodium Hypochlorite is also widely used in conventional laundry operations.

Sodium Perborate - A common oxidizing bleach used in pre-cleaning and spotting operations . It is a highly alkaline substance and is normally neutralized with acetic acid after application.

SolvairTM Drycleaning System - A closed-loop drycleaning process which uses SolvairTM Fluid or dipropylene glycol n-butyl ether (dipropylene glycol normal butyl ether) as a base cleaning fluid and then uses liquid carbon dioxide to rinse the garments.

SOLVATION Process - A solvent vapor recovery process in which an air stream is continuously circulated through the drycleaning machines condenser, a water bath and the hot clothes in the machine’s tumbler. When passing through the water bath, the air stream becomes saturated with water. The perc and water in the air stream leaving the stream becomes saturated with water. The perc and water in the air stream leaving the bath form an azeotrope, which has a lower boiling point than perc alone, thereby increasing the ability of the machines standard condenser to recover the solvent vapor.

Solvent Mileage - The amount of fabric cleaned per a quantity of solvent; a measure of the efficiency of a drycleaning system. Also known as Solvent Consumption.

Solvent Pump - A pump located in the drycleaning machine that circulates solvent in the machine.

Solvent Relative Humidity - The moisture content of drycleaning solvent with added detergent is expressed as a percentage of the amount of water carried by the detergent in the solvent compared with the maximum amount of water which the detergent in the solvent will carry.

Solvent Relative Humidity Instrument - A moisture control device that collects solvent, air, and moisture vapors from the wash wheel, passes them over a sensing element that measures solvent relative humidity, and automatically injects water in the washer when the relative humidity drops below a pre-determined setting.

Solvent Stabilizers - Chemicals added to solvents to prevent solvent degradation. Stabilizers are predominantly “acid acceptors” that prevent solvents from becoming acidic and therefore corrosive. Generally solvent stabilizers comprise no more 0.2 % (by volume) of the solvent/stabilizer mixture. Some of the stabilizers that have been added to perchloroethylene drycleaning solvent include: cyclohexene oxide, beta-ethoxy proprionitrile, n-methyl morpholine, 4-methoxyphenol, tripropylene, and benzotriazole.

Solvent Turnover - Total gallons of distilled solvent that must be replaced to the system for each 100 pounds of fabric cleaned.

Spin Disk Filter - A device containing 36 fifteen-inch diameter disks of polyester fine mesh material mounted on a hollow central shaft with a motor drive to spin the shaft. Solvent enters the center housing through the hollow central shaft. The filter can utilize either filter powder or to be powderless. Also known as a Centrifugal Disc Filter.

Spot Bleaching - The use of a bleach in pre-cleaning or spotting operations.

Spotting or Pre-spotting - The selective application of chemicals, steam, detergent and/or water to loosen or remove specific stains from soiled garments. Spotting is sometimes done prior to drycleaning (pre-spotting or pre-cleaning) but may also be necessary following drycleaning to remove stubborn stains. Also known as Pre-cleaning.

Spotting Board - A work surface for pre-cleaning and spotting work. The spotting board is normally supplied with steam, compressed air and water.

Spotting Agent - A chemical used to clean or bleach stained or heavily soiled areas on clothing. Spotting agents are generally divided into three classifications: dry-side agents (used to clean non-water soluble stains or soiled areas), wet-side agents for water soluble stains or soils, and bleaches which oxidize or reduce stains or soiled areas.

Standard Cartridge Filter - A cartridge filter (carbon core, all carbon or carbonless) that has dimensions of 7 5/8 inches by 14 1/4 inches.

Steam Cabinet - See Drying Cabinet.

Steam Press - A machine used in the finishing process that utilizes steam to press clothing after it has been drycleaned. A steam line from the boiler supplies steam to the press. The garment is held in place on the press by means of a partial vacuum generated by a vacuum unit. The garment is pressed by lowering the press on the garment and pressing a foot pedal that releases the steam. The condensed steam is evacuated by the vacuum unit. See Grid-Head Press and Hot-Head Press.

Steam Stripping - A method to extract additional solvent from distillation residues during the distillation process. In this method, steam is injected directly into the distillation residues in the still. This causes the boiling point to drop and the distillation rate to increase.

Steam Sweeping - A technique used during the final stage of still boil down to recover as much solvent as possible. In this technique, live steam is swept across the still just above the liquid residue. This results in a temperature increase and a resulting additional recovery of solvent.

Still - A device used to volatilize and recover solvent from contaminated solvent.

Still Bottoms - The waste sludge or solid residue from the still. Still bottoms contain solvent, water, soils, carbon and other non-volatile residues. Still bottoms from chlorinated solvent drycleaning operations are hazardous wastes. Also known as Distillation Bottoms, Distillation Residues, Still Residues or Sludge.

Still Kettle - The vessel in which the distillation process occurs.

Still Residues - See Still Bottoms.

William Joseph Stoddard - (1878 - 1940). An American drycleaner from Atlanta who worked with the petroleum refining industry to develop a higher flash petroleum drycleaning solvent (now referred to as Stoddard solvent) in 1924.

Stoddard Solvent - A petroleum drycleaning solvent which is a blend of petroleum distillate fractions (C7 - C12). It is composed of 30 - 50% straight and branched chain alkanes, 30 - 40% cycloalkanes, and 10 - 20% alkyl aromatic hydrocarbons.

Streaks - See Swale.

Surfactant - The term surfactant is short for "surface active agent". It is a chemical that stabilizes mixtures of oil and water by reducing the surface tension at the interface of oil and water molecules. The addition of a surfactant prevents an oil/water mixture from separating into layers.

Suzie - A device that blows steam and air through a garment to reduce wrinkling and facilitate pressing and finishing. Also known as Form Finisher.

Swale - Uneven deposit of non-volatile material on a garment. Also known as Streaks.

Sweetener Powder - A type of filter powder that is composed of activated clay. These clays are adsorptive and will remove soluble impurities from solvent such as detergents, fatty acids and dyes. This powder has been used with filter powder to avoid filter clogging.

Synthetic Detergents - A liquid or solid material able to dissolve oily materials and disperse them or emulsify them in water.

T

Tannin Formula Agents - Spotting or pre-cleaning agents used to clean tannin stains. A tannin formula is a mixture of an acid and a neutral lubricant.

TCA - See 1,1,1-Trichloroethane.

TCE - See Trichloroethylene.

Tech Kleen® - An n-propyl bromide based drycleaning solvent stabilized with 1,2-epoxybutane. Tech Kleen® is marketed by Tech Chem.

Temporary Vapor Storage (TVS) - An emission reduction technology which provides for efficient, economic recovery and temporary storage of perchloroethylene vapors using a high capacity polymeric adsorbent.

Tetrachloroethylene or Tetrachloroethene - See Perchloroethylene.

Tetrachloromethane - See Carbon Tetrachloride.

Third Generation Drycleaning Machine - A closed-loop (dry-to-dry) drycleaning machine equipped with a refrigerated condenser.

Titanium Stripper - A common reducing bleach used on dye stains and to make whites whiter. The active ingredients are titanous sulfate (10 - 15%) and 1 - 4% sulfuric acid.

Tonsil® Filter Aid - A filter powder composed of acid activated calcium bentonite. It is used with spin disc filter systems in hydrocarbon solvent dry cleaning machines.

Transfer Machine - Drycleaning system in which the washing and drying operations take place in two separate units. Some transfer operations have employed three machines: a machine where the clothing is washed; an extractor, where the solvent is extracted from the clothing by centrifugal force; and a dryer (tumbler or reclaimer). Also known as a Cold Machine or a First Generation Drycleaning Machine.

1,1,1-Trichloroethane (TCA) - a.k.a. methyl chloroform, a chlorinated solvent that was formerly used to limited extent as a primary drycleaning solvent (particularly in leather cleaning operations) and was a common dry-side spotting agent. There were problems with equipment corrosion in TCA drycleaning operations. See Dowclene Ls.

Trichloroethylene or Trichloroethene (TCE) - A chlorinated solvent that has been used as a both a drycleaning solvent and a dry-side spotting agent. One problem with TCE is that is causes bleeding of many acetate dyes.

True Soap -An early type of drycleaning detergent. True soaps are colloidal sols or gels composed of soap and fatty acid mixtures.

Tubular Filter - A cylindrically shaped, fine-mesh screen supported internally by a coiled wire. These elements are hung vertically from a manifold inside the filter. Solvent flows inward through the walls of the elements, then upward. These elements often are coated with a precoat of powder filter to prevent clogging and maintain proper cake porosity.

Tumbler - A dryer in a transfer operation that vents dryer vapors to the atmosphere. Also known as Non-recovery Unit or Tumbling Unit.

Tumbling Unit - See Tumbler.

Turpentine Spirits - One of the earliest drycleaning solvents. It is produced from the distillation of pine tar.

Two Bath System - A system in which garments are first run through a solvent/detergent wash cycle and then, to remove residual detergent and soils, through a relatively pure solvent “rinse” cycle.

V

Vacuum Still - A device that enables drycleaners to distill petroleum-based solvent safely. In this system, air must be pumped out of the still to create a 26-28 inch vacuum, permitting petroleum solvents to be distilled at reduced temperatures (approximately 100° F) and within safe limits.

Vacuum Unit - A device that collects condensed steam from steam presses and the spotting board. Collection of the steam condensate is by means of a small vacuum pump that is mounted on top of the unit. The condensate water is collected in a tank located at the base of the unit. See Vacuum Water.

Vacuum Water - Wastewater collected through a vacuum line. This wastewater is generated in pre-cleaning, spotting and steam pressing operations. It is contact water and is contaminated with solvent and spotting agents. Vacuum water collected from steam pressing operations is also known as Press Return Water.

Valclene - A Chlorofluorocarbon drycleaning solvent developed by DuPont in the 1960s. Also known as 1,1,2-Trichlorotrifluoroethane, 1,1,2-Trichloro-1,2,2-trifluoroethane, Freon 113, Fluorocarbon 113, CFC 113.

Vapor Adsorber - See Carbon Adsorber.

Vapor Recovery Unit - A device used to trap solvent vapors. The vapor recovery unit can recover perc for reuse from vents of a vented dry-to-dry machine, from a dryer of a transfer machine, or from ventilation vents in the workplace. See Refrigerated Condenser, Carbon Adsorber, SOLVATION, and Temporary Vapor Storage.

Vapor Adsorber - See Carbon Adsorber.

Vented Dry-to-Dry Machine - A refrigerated condensation unit from which all the exhaust vapors are vented to the atmosphere when the drycleaning machine door is opened at the end of the drying cycle. With a vented system, about 85 percent control of solvent vapors is achieved compared to an uncontrolled machine. Also known as a Second Generation Drycleaning Machine.

Vented Refrigerated Condenser - A refrigerated condensation unit that vents exhaust vapors to the atmosphere from the cylinder when the machine door is opened at the end of the drying cycle.

Ventless Refrigerated Condenser - A refrigerated condensation unit which does not vent vapors to the atmosphere.

W

Washer (drycleaning) - A machine used to clean clothing by immersing and agitating them in solvent.

Washer-Extractor - The heart of the drycleaning machine. It contains a horizontal, perforated drum or cylinder that rotates within an outer shell. The shell holds the solvent while rotating drum holds the garment load. The machine first washes the garments then extracts the solvent by rotating at high speed. In a “hot” or dry-to-dry machine, the washer-extractor also serves as the reclaiming dryer.

Water Separator - A device that utilizes gravity to physically separate water that has become mixed with the drycleaning solvent. Water separators are found on stills, dryers, muck cookers and vapor recovery units. They prevent the water from returning with the solvent to the solvent storage tank.

Water Soluble Soil - Soil which dissolves in water. Such substances include: sugar, starch, gums, salt, flavoring agents and syrups, as well as a variety of substances found in foods and beverages.

Wetcleaning - A professional cleaning technique that uses detergents and water. Specialized machines are used that can be programmed to control such variables as mechanical action, water drying temperature, moisture levels in the dryer and water and detergent volume.

Wet-side Spotting Agent - A pre-cleaning or spotting chemical used to remove water- soluble stains or soils. Examples of wet-side spotting agents include: water, synthetic detergents, ammonia, acids and alkalis.

Wet Wash - See Laundering.

Wheel - The cylinder rotating drum or tumbler within the washer-extractor of a drycleaning machine.

Wholesale Supply Facility - A commercial establishment that supplies drycleaning solvents and drycleaning supplies to drycleaning facilities.